Skip to main content
Sign in

What are 'Event' and 'Result' Types?

  • Updated

ProdataKey allows you to use different conditions for rules and Reports.

'Event' types occur when credentials are used, a hardware event occurs, or certain changes are made in the system

'Result' types occur as a result of an Event in the system.

 

Event Types

Below are the Event Types available in PDK.io.

  • AutoOpen Enabled - An Auto-Open event occurred on the device.
  • AutoOpen Disabled - Auto-Open event ended on the device.
  • Credentials Input - A credential (PIN/card/mobile/Touch) has been used at the device.
  • Open (DPS) - The door position sensor input detected the device was opened
  • Close (DPS) - The door position sensor input detected the device was closed
  • Request to Exit Open - The request to exit input was triggered on the device
  • Request to Exit Closed - The request to exit input was cleared on the device
  • Propped Alarm - The door propped alarm has triggered for the device. 
  • Propped Alarm Clear - The door propped alarm has been cleared for the device.
  • All Prop Clear - All door propped alarms have been cleared.
  • Forced Alarm - The door forced alarm has triggered for the device.
  • Communication Loss - Communication to the connection has been lost. 
  • Communication Loss Clear - Communication to the connection has been re-established.
  • Known Person - A valid credential, assigned to a person in the system, was used at a device.
  • No Person Associated with Credentials - An unknown credential was used and access was implicitly denied, unless allowed by a System Event rule.
  • Access Denied - A valid credential, assigned to a person in the system, was used at a device and access was denied.
  • Access Allowed on Multiswipe - A valid credential, assigned to a person in the system, was scanned multiple times and access was allowed.
  • Access Allowed - A valid credential, assigned to a person in the system, was used at a device and access was allowed.
  • Duress PIN Entered - A duress PIN was used to authenticate at the reader.
  • Any Duress PIN Entered - When any duress PIN is used to authenticate at the reader.
  • Entity Added - An entity (Person, Group, Connection, etc) was added to the system.
  • Entity Modified - An entity (Person, Group, Connection, etc) was modified.
  • Entity Removed - An entity (Person, Group, Connection, etc) was removed/deleted.
  • Open (Lock) - A device was activated/opened/unlocked.
  • Close (Lock) - A device was deactivated/closed/locked.
  • Try to Open - An activation command was sent to the device, either through States or a 3rd-party integration.
  • Try to Open for Some Time - An activation command, with extended activation time, was sent to the device, either through States or a 3rd-party integration.
  • Do Not Disturb - The “Do Not Disturb” status of the device was changed. On DND status, the door is locked and unresponsive to regular access attempts until the DND status is removed.
  • Force Toggle - The current state of the device was toggled between open/closed and then maintained in the new state. If a device is deactivated/closed/locked, the Force-Toggle command changes the State to activated/open/unlocked. If a device is activated/open/unlocked, the Force-Toggle command changes the State to deactivated/closed/locked. 
  • Forced Alarm Clear - The door forced alarm for the device has cleared.
  • Card Scan Error - Bad data was received from the card reader connected to the door.
  • Virtual Credentials Input - Upon input of virtual credentials
  • Delay Open (Lock) - A Delayed Open (unlock) command was sent to a device.
  • Delay Close (Lock) - A Delayed Close (lock) command was sent to a device.
  • Open/Close (Lock) - Device toggled open (unlocked) or closed (locked)
  • Overcurrent Detected - Excess or higher than intended current occurred/detected.
  • Overcurrent Cleared - Standard or intended current occurred/restored.
  • Input Power Connected - Expected input power is detected/restored.
  • Input Power Disconnected - Input power is not detected/power loss detected.
  • Low Power Mode On - When low power mode is detected for a controller.
  • Low Power Mode Off - When low power mode ends for a controller.
  • Battery Connected - A battery is connected/detected.
  • Battery Disconnected - A battery is disconnected/lost.
  • Circuit Breaker On - A flood of logged events (40 events in 30 seconds) occurred on either input A or B (DPS or REX respectively), this disables the input for 30 minutes.
  • Circuit Breaker Off - A previously triggered Circuit Breaker event ended.
  • Anti-Passback Violation - An Anti-Passback Violation (a credential previously used for entry was used for entry again without being used for exit between the events) occurred.
  • Anti-Passback Clear - An Anti-Passback Violation event expired, as per the Anti-Passback Event Expiration condition.

 

Results Types

Below are the Result Types available in PDK.io.

  • Known Person - Reports those individuals who are in the system and who accessed a device
  • No Person Associated with Credentials - An unknown credential was scanned and access was implicitly denied.
  • Access Denied - A known credential was scanned and access was denied.
  • Access Allowed on Multiswipe - A known credential was scanned and access was allowed with multiple swipes.
  • Access Allowed - A known credential was scanned and access was allowed.
  • Send Email - When an email is sent
  • Do Not Disturb - Toggles the “Do Not Disturb” status of the door/relay. In Do Not Disturb status, the door is locked and unresponsive to regular access attempts until the DND status is toggled again.
  • Force Toggle - Toggles the current state of the door/relay to open/closed. If a door is closed (locked), toggles to open (unlocked). If the door is open (unlocked), toggles to closed (locked). 
  • Force Open - Holds the door/relay (that the event is created on) in the Open (unlocked) position and will not close (lock) unless Force Closed. 
  • Force Close - Clears the Force Open (unlocked) status and locks the door.
  • Open - Activate/unlocks/opens the device/relay
  • Close - Deactivate/locks/close the device/relay
  • Lockdown On - Lockdown (doors locked) of selected devices is set to On. All doors are locked.
  • Lockdown Off - Lockdown (doors locked) of selected devices is set to Off. All doors are unlocked. 
  • Delay Open - A time delay for opening (unlocking) the door/relay
  • Delay Close - A time delay for closing (locking) the door/relay
  • Open/Close - Opens (unlocks) the door/relay and sends a close (lock) after a delayed time period

Related articles

Comments

0 comments

Please sign in to leave a comment.